How To Remove Office Chair Base

How to remove office chair base!

If your chair casters are worn out and do not function properly, or you have inherited an old broken chair at home, there is no need for despair!

It is possible to fix the chair on your own, and you’ll probably save a lot of money in the process.

You need to follow some simple steps to remove the chair’s base and make the base of your chair work according to the desired condition.

how to dispose of an office chair by


  • A chair base (adjusted to the size of your chair for work)
  • Table vice with wide opening jaws
  • Electric drill with various bits
  • Rubber mallet
  • Grease or simple mallet

Step By Step Guide For Chair Base Removal

how to remove office chair base by

Step 1 :

If the base of your office chair is made from metal, try soaking it in warm water with a few drops of dish soap for around 30 minutes.

The heat and the soap will make the components more flexible and working easy, allowing you to remove the screws and bolts with less difficulty.

If you cannot submerge the entire caning base, place it in a large bowl of warm water.

Step 2 :

Grab your tools like electric drill and a flathead screwdriver attachment bits. Begin by inserting larger, flat bits into the chair’s base to remove the screws that hold it together.

Once you have removed all of them, pull upwards on one side of the office chair furniture.

This should detach many parts of the chair and leave you with a bare metal frame.

Step 3 :

Use your smaller drill bits to remove the bolts that attach the office chair’s base to its wheels.

If you try pulling them out with pliers, these can be easily bent or broken, so you should not use much force when removing them. 

After you have removed the bolts, place both parts of the chair base to the side.

Step 4 :

It would help if you now had a metal frame with no broken pieces attached.

Set up your large table vice as you would if you were trying to bend metal and tighten its jaws around the frame so that they are firmly gripping it.

If your drill bits provide any resistance while removing the bolts from the wheels, you should leave them in place as they will aid you when drilling holes through your frame.

Step 5 :

Insert a drill bit into your electric drill and turn it on. Gently let the tip of the drill bit trace around the opening provided by your bits, slowly drilling a large enough hole for a new bolt to fit through easily.

You may need to turn the metal frame around to get it in the correct position for drilling.

Continue this process until you have drilled holes at all of your former bolt locations, and your office chair base should be ready for reattachment!

Step 6 :

Insert bolts into the holes you have drilled and secure them by tightening the nuts on end with a wrench.

Place your office chair base back onto its wheels, and you should be ready to use it! 

If it feels somewhat unstable, try adjusting the bolts slightly until you get it working at optimum levels of performance.

Precautions For Removing The Base of A Chair

  • Make sure that you have a suitable drill bit for your drill in center of the base.
  • Make sure that the metal part of the office chair is clamped into a table vice securely before drilling holes in it.
  • Keep some pliers on hand in case a bolt becomes stuck while removing them from the wheels of your office chair or if you need to remove them from the base after drilling holes.
  • Keep your drill at a low speed while drilling into the metal parts of your office chair.
  • Make sure that you are using the correct size drill in center of the base bit for your bolts; this will stop any part of the bolt from coming through on the other side, which could cause injury to yourself or damage.
  • Make sure that no one is in the way of your drill while drilling into the metal parts of your office chair.
  • Keep your electric drill at a safe distance from any objects while drilling holes through metal parts of your office chair; you don’t want to cause damage to anything other than the metal parts of your office chair.
  • Make sure that your bolts aren’t too long; you will damage the metal frame of your office chair if they are.
  • Keep a socket wrench on hand in case a bolt is too large or too small for your drill bit size; this allows you to use them instead.
  • If you have no luck with removing bolts by drilling holes around them, try using a hacksaw to break the bolts instead.
  • Try not to over tighten any nuts and bolts as this can cause damage to your office chair and will require replacement parts.
  • Keep pliers on hand in case you need to straighten out bolts that become bent while removing them from metal parts of your office chair or while trying to drill holes through them.
  • Try not to bend over the metal frame of your office chair more than is needed. You don’t want it to become misshapen.
how to remove office chair base by

Why Do We Need To Remove The Chair Base

There could be many reasons why one needs to remove the office chair base.

For example, if someone has a broken chair and wants to replace the old base with a new one.

Or maybe they want to adjust and fix something below the legs of their chair.

Perhaps they want to clean out all the dust and dirt caught between them, or worse, a fire, and the office needs to be rebuilt.

There is no limit to reasons why someone may need to remove an office chair base, but they are all pretty much irrelevant because this article will teach you exactly how to do it.

Tips For Removing The Chair Base

  • If there is just one bolt left in your chair base, try removing it with an extended length of wire hooked around the bolt head.
  • If you are having trouble removing bolts by using a drill bit around them, try using a hacksaw instead to break through any leftover ones.
  • It may be possible to remove the bolts using your bare hands; instead, this will require a lot of strength.
  • If you are having trouble keeping all bolts in place while drilling holes around them, use some blue tack to keep them in the correct position while working on them.
  • Try not to drill too deep, or you might damage other parts of your chair.
  • Keep a socket wrench on hand in case you need to use it instead of your drill for any reason.
  • Make sure that the area around where you are drilling is safe for drilling. There should be no objects or flammable items in this area.
how to remove office chair base by


In summary, the process to remove the cylinder base from an office chair upside is a relatively easy one.

Because it can be pretty challenging to drill through metal with a hand-held drill, you may want to consider renting a power tool for this particular job.

The heat and dish soap help make removing broken bolts much more accessible by making them more flexible.

Be careful not to apply too much force with your drill bits to prevent them from snapping.

Concluding, there is no need for despair when it comes to broken office chair bases!

With a bit of elbow grease and the right tools, you’ll be back on your feet in no time at all.


Q. Is it possible to remove the office chairs base without a drill?

Yes, of course, you can use a wrench, but it is way more complicated. It mainly depends on the type of chair that you have and how much damage has been done. If any bolts or screws are holding your broken base together, you might detach them.

Does it hurt to remove the base of the office chairs with bare hands?

 No, not at all. If you’re careful and take your time, then you won’t have any problems. If the bolts have been there for some time, they might be a bit rusty, but if that’s the case, you can try scrubbing them with an old toothbrush.

Q. Does this method work for repairing chair wheels too?

Yes, it is a good idea to use the same method if you’re trying to repair your wheel by chair upside mechanism as well. If any bolts hold them together, all you have to do is unscrew them rotating counter-clockwise and attach the new ones in easy way.

Q. Is it possible to remove the seat from a chair without removing its base?

Yes, but it is much more difficult and not advised because there might be bolts in the seat, which you’ll have to unscrew before removing it. If you’re trying to clean your chair, we advise that you do so by taking off its seat.

Q. Is it possible to repair a chair base with all the bolts still attached?

Yes, it is actually a good idea that you do this because then you don’t have to worry about trying to get the bolts in the proper position for reattaching your new base. It’s basically like how it was before.